Ein Kehlbalken Dach mit gewählter Geometrie wird in Hinblick auf seine Schnittgrößen zwischen Berechnung mittels RFEM 6 und der Handrechnung verglichen. Dabei werden insgesamt 3 Lastsysteme untersucht.
Este ejemplo de verificación se basa en el ejemplo de verificación 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
El ejemplo de verificación describe las cargas de viento en varias direcciones del viento en un modelo de un grupo de edificios. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum deflection with consideration of initial slippage.
Determinar la flecha máxima y el momento radial máximo de una placa circular simplemente apoyada sometida a presión uniforme, temperatura uniforme y temperatura diferencial.
Una placa ortótropa cuadrada en capas está completamente fijada en su punto medio y sometida a presión. Compare las flechas de las esquinas de la placa para comprobar la corrección de la transformación.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
El modelo de material de Kelvin-Voigt consiste en el muelle lineal y el amortiguador viscoso conectados en paralelo. En este ejemplo de verificación, se prueba el comportamiento temporal de este modelo durante la carga y relajación en un intervalo de tiempo de 24 horas. La fuerza constante Fx se aplica durante 12 horas y el resto de 12 horas es el modelo de material libre de carga (relajación). Se evalúa la deformación después de 12 y 20 horas. Se utiliza el análisis en el dominio del tiempo con el método lineal implícito de Newmark.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Una viga larga y delgada lleva una masa concentrada y está cargada por una fuerza dependiente del tiempo. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Un sistema de una sola masa con juego y dos muelles se deforma inicialmente. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Determinar el desplazamiento máximo, las tensiones en el plano y las relaciones de tensiones de una placa de vidrio de doble panel simplemente apoyada con una lámina entre ambos paneles de vidrio sometida a una presión uniforme.
Una viga de acero con una sección cuadrada está cargada con un esfuerzo axil y una carga distribuida. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Un recipiente de paredes gruesas está cargado por una presión interna tal que el recipiente alcanza un estado elástico-plástico. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Considere una viga W 18 x 50 según ASTM A992 para el vano y cargas vivas y muertas uniformes como se muestra en la figura 1. La barra está limitada a un canto nominal máximo de 18 pulgadas. La flecha de la carga viva está limitada a L/360. La viga está apoyada y arriostrada continuamente. Verifique la resistencia a flexión disponible de la viga seleccionada, según LRFD y ASD.
Un cable o membrana de acero con pasadores en ambos extremos se carga mediante una carga distribuida. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Un recipiente de dos capas, de extremos abiertos y paredes gruesas está cargado por una presión interna y externa; por lo tanto, no hay tensión axil. While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.
Un voladizo está completamente fijo en el extremo izquierdo y cargado por una fuerza transversal y una fuerza axil en el extremo derecho. The tensile strength is zero and the behavior in the compression remains elastic.
Verifique que una viga de diferentes secciones hecha de la aleación 6061-T6 sea adecuada para la carga requerida, de acuerdo con el Manual de diseño de aluminio de 2020.
Demuestre que el acoplamiento de diferentes elementos dimensionales no afecta a los resultados. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Un voladizo de sección rectangular tiene una masa al final. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Consider an ASTM A992 W 18×50 beam forspan and uniform dead and live loads as shown in Figure 1. La barra está limitada a un canto nominal máximo de 18 pulgadas. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
El ejemplo de verificación describe el flujo estacionario alrededor de un edificio de gran altura entre bloques de apartamentos (modelo a escala). The example is given by the Architectural Institute of Japan (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
Determine las flechas máximas del bloque considerando o omitiendo el efecto cortante. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Una placa compuesta que consta de tres capas de vidrio, una capa de lámina y un espacio interior con aire seco, está completamente fijada y cargada con una temperatura variable. Neglecting its self-weight, determine the plate's maximum deflection.
Un disco compacto (CD) gira a una velocidad de 10.000 rpm. Therefore, it is subjected to centrifugal force. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Se omite el peso propio. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Una membrana se estira por medio de un pretensado isótropo entre dos radios de dos cilindros concéntricos que no se encuentran en un plano paralelo al eje vertical. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.